Frequently Asked Questions

Frequently Asked Questions

No. Although often used interchangeably – even by some construction professionals – cement is not concrete nor is concrete cement.

CEMENT is one of the basic ingredients used to make CONCRETE … just as FLOUR is one of the basic ingredients used to make CHOCOLATE CHIP COOKIES. When cement is mixed with other basic ingredients — sand, gravel or crushed stone, and water– the cement and water react to form a paste that glues the remaining ingredients into a rock-like mass which is known as concrete.

Slump is used as a measure of consistency of concrete, and is most often associated with the amount of water added to the concrete mix to increase ease of placement (the higher the slump, the wetter the mix).

The addition of water to increase slump beyond the design specification will result in reduced-strength potential for the concrete and possible surface deterioration. Quality Utah contractors place concrete for exterior pavement applications at a moderate slump — not more than 4 to 5-inches — unless a water-reducing admixture is used.

When added to the concrete mix at the batch plant, fiber-reinforced concrete creates a uniform system of millions of polypropylene fibers, which are formulated to address early-age cracking problems caused by water loss and shrinkage.

Ordering ready-mix concrete from American Eagle Ready Mix must be done by calling our Central Dispatch office, who will fill your order from the closest plant location. Before you call, measure your project and create a scale drawing, including the actual dimensions. Also, when filling out your project form, please indicate concrete by volume, expressed in cubic yards.
Be prepared to share the following information with our Central Dispatch:

  • Name
  • Project address
  • Directions to project site
  • County the project is located in
  • Job site phone number and contact (land-line or cell)
  • Date and time concrete is required
  • Volume of concrete needed, in cubic yards
  • Concrete mix desired
  • Intended use (driveway, patio, basement floor, etc.)
  • Desired slump
  • Description of available truck access
  • Interval between loads (if more than nine yards of concrete are required)
  • Concrete placement method (chute, wheelbarrow, concrete pump, or the like)
  • Payment method.

Ready-mixed concrete is sold by the cubic yard. If you can determine the area of your concrete project (length x width for rectangular projects) and know the thickness of the slab, you can determine how much concrete you need by using a concrete calculator, which can be found using a simple Google search. For liability reasons, we will not calculate your project volume for you.

Delivery hours are Monday through Friday, 6:00 a.m. to 4:30 p.m., and Saturdays, 6:00 a.m. to Noon. Saturday hours are seasonal in nature and subject to the number of confirmed orders received. Please note that we also charge an additional “per truck” fee for Saturday deliveries.

Holidays hours are determined on a case-by-case basis. Know our employees work long, hard hours throughout the year and, like you, want and deserve time off to spend with family and friends.

Advance notice is strongly recommended to permit scheduling of vehicles needed to deliver the concrete to the job site and to allow for batching, loading, and mixing times prior to departure for the job site. A 48-hour window is a reasonable time frame during the construction season.

Orders may be cancelled a minimum of two hour prior to scheduled delivery time. Once the concrete is on the truck, it’s yours! Orders before 8 am that are cancelled the morning of may be subject to late cancellation fees.

The base cost is dependent on the type of mix design used for the particular project application involved. Additional costs for minimum loads, waiting times, and sales tax will also be included in the total charge. The dispatcher will provide cost information, based on your specific project situation.

Payment is due at the time of delivery (C.O.D), unless you have an account set up with American Eagle Ready Mix. C.O.D payment may be made by cash or credit card. All C.O.D. orders must be paid for before we will send out the order.

Placing and finishing ready-mixed concrete is not rocket science. It is also not child’s play. Placing and finishing concrete requires knowledge about concrete and the fundamentals of good concreting practices. It requires skill with both basic tools – including hammers, tape measures, chalk lines, saws, and a hose – and specialized concrete tools, including come-alongs, a straightedge, a concrete edger, a bullfloat, a hand float, and a groover (jointer), to name a few.

If organization, planning, and project management skills are not your strong suit, you would best be served by hiring a construction professional for your concrete project. Site excavation, subgrade preparation, and building and setting concrete forms are not easy tasks for most do-it-yourselfers.

Placing and finishing concrete is hard work. Concrete is heavy – about 150 pounds per cubic foot – and difficult to place, consolidate, strike off, level, and finish. Timing of many finishing operations is crucial and best learned through experience. Mistakes in timing may prove critical. As the National

Ready Mixed Concrete Association’s Finishing Concrete Flatwork publication points out, “Any finishing operations undertaken while the concrete slab is still “bleeding” will result in problems for the finished slab, such as scaling, cracking, delamination, dusting, or concrete blisters.” Bleeding characteristics for concrete can vary, based on mix design, subgrade preparation, and weather conditions, and can often challenge experienced contractors.

Yet for some do-it-yourselfers, the hard work and high-degree of skill, management, and adventure required to complete a successful concrete project provides a unique sense of satisfaction. If this describes you, and you can muster enough friends to safely and efficiently transfer concrete from the ready-mix truck into preset, well-braced forms, go for it.

American Eagle Ready Mix works with reputable residential concrete contractors across Salt Lake and Utah counties daily and can help you find contractor candidates for your concrete project. Our dispatchers are happy to make recommendations and provide referrals for quality contractors to meet your needs.

The empty weight of an American Eagle Ready Mix front-discharge concrete transit mixer with typical levels of fuel and water is around 36,000 pounds and will double in weight with a full 9-yard concrete load. The height of our vehicles can be up to 13.6 feet; the width of our vehicles is 8.6-feet, a mirror to a mirror. The consequences of moving equipment of this size onto your property to facilitate unloading times must be carefully considered.

Only if the driver determines the situation is safe, with the additional requirement of a signed waiver of release by the homeowner for all movement past the curb line.

Your American Eagle Ready Mix driver will take the following factors into consideration:

  • can the slope leading to your project be safely navigated?
  • can the ground to and surrounding the project support the weight of the loaded truck?
  • can the truck maneuver safely under power lines, tree limbs, roof eaves, and other overhead obstructions
  • can the truck maneuver safely through the opening available to reach the project?

The chute systems on American Eagle Ready Mix vehicles typically reach up to 18 feet.

For most homeowner concrete projects, the truck chutes and/or use of a wheelbarrow or concrete buggy will be sufficient for unloading and placing the concrete. The need for a concrete conveyor or concrete pump will be dictated by your particular job site circumstances. There is a separate charge for these types of material placement services.

American Eagle Ready Mix works with the best concrete pumping/conveyor service contractors in Salt Lake and Utah counties and is happy to provide recommendations and contact information for you.

Concrete is a perishable product, and most specifications require it be discharged on the job site within 90 minutes or 300 revolutions of the truck barrel, after the addition of water to the concrete mix at the batch plant. Allowable unloading time at the job site is 10 minutes per yard. Thus, a 9-cubic yard load of concrete would be expected to be unloaded in 90 minutes or less. Charges in excess of allowable times are $30 per 15 minutes.

There is no typical or specific time frame for working with in-place concrete, due to the many variables involved, such as mix design, ambient temperature, wind velocity, and placement location (indoors/outside), to name a few.

For these, and reasons stated above, the use of a qualified concrete contractor is highly recommended, unless you and members of your placing and finishing team have prior experience in placing and finishing concrete.

Brooming of the concrete surface provides a safe, attractive, non-slip surface for exterior concrete flatwork. Broom finishes are created by pulling a special dampened, stiff-bristle concrete texturing broom across freshly floated concrete, and can be applied in many ways, including straight, curved, and wavy lines.

Most broom finishes for concrete sidewalks and driveways are straight-line textures broomed at right angles to the anticipated traffic direction. Broom finishes are not incorporated into most decorative concrete finishes.

Curing is the procedure for maintaining an acceptable moisture content and temperature profile in the concrete to ensure desired properties of the concrete are achieved. Testing demonstrates improper or lack of curing can cut the strength of a proper concrete mix by as much as 50%. The potential for concrete shrinkage, cracking and dusting increases significantly when concrete is not cured correctly.

The American Concrete Institute and the American Concrete Pavement Association recommend a minimum of seven days following concrete placement before using a concrete driveway. Other concrete industry educational and technical societies recommend anywhere from three-to-seven days after placement, depending on anticipated driveway loading factors and the concrete mix design used.

Consult with your concrete contractor regarding when you can place your new driveway in service.

While a curing compound acts to prevent moisture from leaving the concrete during initial stages of strength development, a concrete sealer is designed to prevent moisture from entering the concrete matrix, to assist in limiting surface deterioration due to cycles of freezing and thawing. New concrete should air dry for 30 days prior to the application of a concrete sealer. Follow the manufacturer’s directions for application rates and intervals. Many sealer applications are effective for a two-year period.

The use of deicing chemicals during the first year of service is not recommended, especially if concrete is installed late in the year. Sand is an acceptable alternative anytime. Deicing chemicals used for snow and ice removal can cause and aggravate surface scaling. Therefore, judicious use of these products with regard to amount and frequency of application is strongly advised.

Remember deicers can also reach concrete surfaces other than by direct application — for example, drippings from the undercarriage of vehicles. During and after the concrete’s second winter, deicing chemicals containing sodium chloride (common salt) or calcium chloride may be used judiciously.

NEVER use deicers containing ammonium sulfate or ammonium nitrate, as they will chemically attack and rapidly disintegrate concrete.

ALSO NOTE: common garden fertilizers often contain ammonium sulfate and/or ammonium nitrate and can cause disintegration of your concrete. Avoid loading or cleaning your fertilizer spreader on your concrete slab and follow best-spreading practices by applying fertilizer around the periphery of your lawn first, without crossing pavement, then run the spreader back and forth within the area bounded by your perimeter fertilizer run. This practice both ensures consistent fertilizer application around the edge of your lawn and, because the spreader never crosses pavement, minimizes the potential for fertilizer damage to your concrete.

Frequent cleaning keeps your new concrete looking good and does wonders to improve the curb appeal of your home. By keeping your concrete clean by frequent sweeping and occasional hosing, you can also significantly reduce fall risks to family and guests. Wet leaves left on a driveway will have a tendency to stain, so be prepared to clean your driveway often in fall. Leaf stains can be cleaned away with a pressure washer (light pressure) or with hot water mixed with tri-sodium phosphate (one pound per gallon is recommended).

Area banks, savings and loans, and credit unions have many financing options for home improvements. Their loan officers will be happy to help you compare interest rates, payment options, and tax advantages and will work with you to figure out the best option for your financial situation. The most likely financing options will include cash-out refinancing, home equity credit lines, second mortgages, and home improvement loans.

Mechanic’s liens exist to provide collection rights to contractors and material suppliers who supply construction services or materials for improvements to real property. Waiver-of-lien forms provide protection for homeowners who pay their home improvement bills. With a mechanic’s lien, the concrete supplier or concrete contractor has the right to serve the homeowner with notice of lien and to record it as part of the county land-title records, should payment not be made for materials or services provided. A lien is a claim of partial ownership of your home.

If the mechanic’s lien is not paid, the material supplier or contractor can commence court proceedings to foreclose the lien and sell the property in payment of the obligation. A waiver-of-lien form provides a homeowner proof that subcontractors and material suppliers have been paid and relinquish their right to serve the homeowner with a notice to place a lien the home.

The case history that follows explains why lien waivers are important to homeowners: Mr. Jones signed a contract with ABC Contractors for the construction of an addition to his home. When the work was done, Jones paid the contracted price and started enjoying his new addition. A month later, he received a “Notice of Intent to File Claim for Lien” in the mail from the lumberyard where ABC Contractors obtained building materials.

What happened?

Although Jones had paid his bill, ABC Contractors did not pay the lumberyard. The law allows a subcontractor or supplier of materials to place a lien on the property where the work was done if the contractor doesn’t pay his bills. This can happen even if the homeowner has paid the contract in full.

To protect against similar circumstances, we recommend calling to ensure that materials have been paid for in full before paying your contractor out for the project.

You are best served by hiring a concrete contractor who has proper insurance coverage, including liability insurance covering property damage and worker and public injuries, vehicle insurance, and workers’ compensation insurance.

Consumers’ Report cautions homeowners to get written proof of these policies.

Once you start thinking in earnest about your concrete project, contact your insurance agent regarding necessary safeguards.

Terms and Conditions

When you provide us with your mobile phone number, you agree that American Eagle Ready Mix LLC may send you text messages (including SMS and MMS) to that phone number. You will receive a confirmation text message, and you may need to reply as instructed to complete registration. The frequency at which you’ll receive our text messages may vary from month to month. Message and data rates may apply. Reply STOP to cancel, HELP for help. You agree to receive a final text message confirming your opt-out. You may opt-out at any time by texting the word STOP to the number 801-438-8490. For help, send a text message with the keyword HELP to the number 801-438-8490. Texts may be sent through an automatic telephone dialing system. Consent is not required to purchase our goods or services. You agree to notify us of any changes to your mobile number and update your account us to reflect this change. Your carrier may prohibit or restrict certain mobile features and certain mobile features may be incompatible with your carrier or mobile device. Contact your carrier with questions regarding these issues.

All you have to do is text join to 801-438-8490. (Message frequency may vary, message and data rates may apply, and you can always text HELP for help & STOP to cancel). When you opt-in to the service, we will send you an SMS message to confirm your signup.

If at any time you forget what keywords are supported, just text HELP to 801-438-8490. After you send the SMS message HELP to us, we will respond with instructions on how to use our service as well as how to unsubscribe.

You can cancel the SMS service at any time. Just text STOP to 801-438-8490. After you send the SMS message STOP to us, we will send you an SMS message to confirm that you have been unsubscribed. After this, you will no longer receive SMS messages from us. If you want to join again, just sign up as you did the first time and we will start sending SMS messages to you again.

American Eagle Ready Mix LLC will never charge you for the text messages you receive however standard message and data rates may apply for any messages sent to you from us and to us from you. If you have any questions about your text plan or data plan, it is best to contact your wireless provider. For all questions about the services provided through the number 801-438-8490, you can send an email to asmata@aermut.com.

United States

We are able to deliver messages to the following mobile phone carriers: Major carriers: AT&T, Verizon Wireless, Sprint, T-Mobile, MetroPCS, U.S. Cellular, Alltel, Boost Mobile, Nextel, and Virgin Mobile. Minor carriers: Alaska Communications Systems (ACS), Appalachian Wireless (EKN), Bluegrass Cellular, Cellular One of East Central IL (ECIT), Cellular One of Northeast Pennsylvania, Cincinnati Bell Wireless, Cricket, Coral Wireless (Mobi PCS), COX, Cross, Element Mobile (Flat Wireless), Epic Touch (Elkhart Telephone), GCI, Golden State, Hawkeye (Chat Mobility), Hawkeye (NW Missouri), Illinois Valley Cellular, Inland Cellular, iWireless (Iowa Wireless), Keystone Wireless (Immix Wireless/PC Man), Mosaic (Consolidated or CTC Telecom), Nex-Tech Wireless, NTelos, Panhandle Communications, Pioneer, Plateau (Texas RSA 3 Ltd), Revol, RINA, Simmetry (TMP Corporation), Thumb Cellular, Union Wireless, United Wireless, Viaero Wireless, and West Central (WCC or 5 Star Wireless).

Canada

Bell (including NorthernTel, Solo Mobile, and Telebec), Fido, MTS, Rogers, SaskTel, Telus (including Koodo Mobile and Public Mobile), Videotron, Virgin Mobile, and Wind.

***This service and the carriers are not liable for delayed or undelivered messages***